My new Kobra Max just arrived. I can’t believe the size of the print area!1yr ⋅ SomeDudeFromSpace ⋅ r/anycubic
Shout out to Anycubic support. I submitted my support ticket a week ago and this replacement got to my door today.5mo ⋅ MrGulio ⋅ r/anycubic
Not too much space in my room so I had to improvise, meet the abomination.4mo ⋅ Jamesgeorge96 ⋅ r/anycubic
My first 3D print. I think it was supposed to be an owl. It shifted at least 3 times during the print1yr ⋅ Sad_Reserve_7393 ⋅ r/anycubic
Desert burrower dragon printed on anycubic photon. All primed and ready to paint! Amazed out how detailed it can get! Resin for life.4yr ⋅ austinbatch ⋅ r/anycubic
This id how every PETG print starts... Bed is levelled with the Marlin software. 235°C extruder and 80°C bed temps. It is really frustrating....2yr ⋅ Eierquetscher ⋅ r/anycubic
Looking for a little help. My printer does great prints but the top and bottom have these little misses. Ideas?2yr ⋅ cowboyfromhell324 ⋅ r/anycubic
Started from the bottom... finished calibrating my Kobra Original for PETG1yr ⋅ VampyreLust ⋅ r/anycubic
What is this tool/thing that came with the Kobra 2 Neo? It isn't listed on any instructions.1mo ⋅ SevRoks ⋅ r/anycubic
New Kobra Max! From box to printing was less than 45 minutes. Impressive!1yr ⋅ xontinuity ⋅ r/anycubic
I'm so frustrated. ABL doesn't do it's job. one side is good the other side is too close.1yr ⋅ 1309Log ⋅ r/anycubic
Any idea why I get layer gaps like this? Kobra Go using provided profile 195/60 temp PLA .2mm1yr ⋅ beanieb22 ⋅ r/anycubic
Someone has a idea why my printer started with this BS today and how I can fix this?1yr ⋅ Sebastian1989101 ⋅ r/anycubic
I bought my first 3D-printer from Anycubic, and it's the Mega X, yesterday and I love it 😍💪2yr ⋅ Conscious_Board5007 ⋅ r/anycubic
Skirt is darker on the left than the right? How do I get the bed level when it's already done autoleveling!?1yr ⋅ spacemidget75 ⋅ r/anycubic
Does anybody know why this happens? The bed and hot end both heat up, the axis home themselves, and the print starts, but right as the nozzle hovers over the bed this error occurs.1yr ⋅ Bgats9 ⋅ r/anycubic
Elf on Dire wolf print turned out fantastic. Printed on anycubic photon.4yr ⋅ austinbatch ⋅ r/anycubic
Mega S - I upgraded my steppers and calibrated my E. Good quality prints but I'm getting travel dragging which I didn't have before?4yr ⋅ MasterXL6 ⋅ r/anycubic
Any slicer (Cura) tips that could help these strange gaps from showing? Printer: Anycubic Kobra Go1yr ⋅ christiandelucs ⋅ r/anycubic
HELP! Kobra Max Filament Error every 5-10 min. Can I turn the sensor off?1yr ⋅ maxxim2000 ⋅ r/anycubic
The Kobra Max is a beast. I don't think it's going to fit on my printing cabinet with it's cousin the Vyper.1yr ⋅ fm67530 ⋅ r/anycubic
Hey anycubic hive mind Unfortunately since I upgraded my stepper drivers to TMC2209s and Marlin I've been having consistent issues with y axis layer shifts. This doesn't happen with the stock firmware, only when I have Marlin on. Any ideas? Put what I've tried in comments3yr ⋅ Adduly ⋅ r/anycubic
Just got a Mono X... and it cured all the resin inside the vat, turning it into a block2yr ⋅ jasonrodriguez_DT ⋅ r/anycubic
Anycubic Vyper Issue: How do I fix this unholy amount of stringing? My retraction is 6mm at 50mm/s1yr ⋅ A_Shiny_Dunsparce ⋅ r/anycubic
Which Z-Offset? 0.0 has adhesion issues making it look like water is running under it. 0.05 is thinner but smooth to the touch and 0.1 is shinier and has ridges you can feel with a finger nail. 0.15 lifts and burns1yr ⋅ SnooConfections1282 ⋅ r/anycubic
My upgrade i3 mega. Is it an i3 mega anymore? Got bored, thought I'd share. It prints, still work in progress.3yr ⋅ joesavu ⋅ r/anycubic
Do I need to keep this blue plastic part in place? It is very loosen and I thought it was here just for transport purposes.1yr ⋅ zyssai ⋅ r/anycubic
Need help with stringing. Teaching tech gcode (left) is perfect but when i replicate it in cura i get left1yr ⋅ ephemeralkazu ⋅ r/anycubic
I listened to all of your help. 210°c hotend 60°c bed 40m/s print speed, 6 layer height, pla, 10% infill2yr ⋅ hdjsbdjsbdms ⋅ r/anycubic