Whenever I screw a board to another board, one of the boards will always move slightly. Am I doing something wrong? Is there a way to prevent this?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
Tried making a half-lap joint with my circular saw, results were not good and I would greatly appreciate help1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
Tried glueing these four studs to this plywood and none of they stayed put. What do I need to do differently?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
If I put a 3/4in thick piece of plywood on top of this, would it be able to support my 150lb table saw?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
Once bolted down, I feel like this feather board layout is the most optimal for kickback prevention (thoughts?)1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
How should I remove the remaining rust from this Jointer so that I don't mess up it's flatness?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
What bin/storage type is best for actually being able to store a lot of screw?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
In order to get this clamp to work properly, would I have to tap and die the hole that this thread goes into?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
Does Fresno/Clovis have any dimmy lit / seductive-vibe bars or lounges? (Similar to the example photo) 3wk ⋅ longbdingaccount01 ⋅ r/fresno
Can I make this shape out of a piece of wood using only a table saw?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
If I want to make these indents is there a specific router bit I should use? And would I put the two pieces of wood on top of each other before routing so they come out the same?9mo ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
XT3 with a 35mm (160 iso, f1.8, 160 ss) New, so greatly would appreciate feedback1yr ⋅ longbdingaccount01 ⋅ r/fujifilm
Would this wooden dolly setup with halflap joints be strong enough to hold a 150lbs table saw?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
A few months ago these were going for $6.00 in my area. At what price would these need to get to for you to be content?1yr ⋅ longbdingaccount01 ⋅ r/woodworking
I'm sorry if this a dumb question, but when cutting sheets of plywood on a table saw do you always still use the fence or miter gauge?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
Hey all! Would there be an way to speed up this process of adding a ton of vocab words?1yr ⋅ longbdingaccount01 ⋅ r/Anki
Does anyone know where I can find a right angle plastic piece for this dust collection port? (tried googling it but not sure what it would be called)1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
My first version of a router sled. Going to eventually upgrade it and if anyone wants to offer any feedback I would be interest2yr ⋅ longbdingaccount01 ⋅ r/Tools
What does it mean when there's a slight gap in the middle of my cross cut, done with a Japanese hand saw? And, how can I prevent it in the future?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
My first version of a router sled. Going to eventually upgrade it and if anyone wants to offer any feedback I would be interest2yr ⋅ longbdingaccount01 ⋅ r/woodworking
Would it be more advantageous to fish up at the top of a dam or at the bottom of a dam?9mo ⋅ longbdingaccount01 ⋅ r/FishingForBeginners
For a drop shot, instead of tying braid directly to fluoro , can I just tie the fluoro to one end of this swivel and the braid to the other end of this swivel? Or would that affect the action of the drop shot?1yr ⋅ longbdingaccount01 ⋅ r/FishingForBeginners
Friend wants a painted mantel above her fireplace, was thinking of using this. Would I need to put some sort of topcoat on top of it or would this alone be fine?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
What's the name of the white tape/tubing that can go vertically on the wall like this and be a pipeline for cable to travel down?1yr ⋅ longbdingaccount01 ⋅ r/DeskCableManagement
Is this a good way to hook up a bait for the drop shot?1yr ⋅ longbdingaccount01 ⋅ r/FishingForBeginners
If I want to make a table that looks like this, what thickness would you recommend that I make the top? Looking to make it 17in x 65in1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
Is there a way to adjust just one edge of a rectangle mask in Fusion?1yr ⋅ longbdingaccount01 ⋅ r/davinciresolve
For a stand like this for a planer, would the wood planks on bottom be necessary for structural stability, or are they mainly just an aesthetic choice?1yr ⋅ longbdingaccount01 ⋅ r/BeginnerWoodWorking
When you get up at 5:30, but Fitbit counts that as time awake 🤦♂️1yr ⋅ longbdingaccount01 ⋅ r/fitbit
Am I better off plugging my Table Saw into Surge Protector or a Portable GFCI Safety Outlet Adapter1yr ⋅ longbdingaccount01 ⋅ r/woodworking
