Any modern pistols similar to Colt 1903 (other than the new ones)? All metal, thin, minimal controls...1yr ⋅ JasonJln ⋅ r/guns
Printed a 150mm long model of the Tachi... 300mm and 500mm models of the Roci are next!4yr ⋅ JasonJln ⋅ r/TheExpanse
Thanks to all who gave input on the Colt M1903 I asked about. Here's a picture to celebrate a new gun purchase!2yr ⋅ JasonJln ⋅ r/guns
When you're 12 hours into a 36 hour print and you notice nothing extruding and the hot end is an inch above the piece.....4yr ⋅ JasonJln ⋅ r/ender3
Posted this on another subReddit. Did not expect the response that it received!4yr ⋅ JasonJln ⋅ r/ender3
My first workbench... 2x7ft. Thinking 1/2 MDF on top of the plywood for a nice smooth surface. No big jobs on this one, electronics jobs, 3d printing, small crafts. Floor isn't level so I'll need to shim it, but it's actually square and even, which is huge for me!4yr ⋅ JasonJln ⋅ r/Workbenches
1195lb trailer welded with Titanium 125 Flux welder. I'm teaching myself here, so perfection this is not. ButI think it'll work...3yr ⋅ JasonJln ⋅ r/harborfreight
Fallen Order lightsaber, 3d print finished painting; first attempt at weathering anything.4yr ⋅ JasonJln ⋅ r/lightsabers
Turns out foam poster board can make an effective ABS enclosure. $5 at dollar store; inside temp stable at 80-85F depending on bed temp and ambient.4yr ⋅ JasonJln ⋅ r/ender3
New LM Bond, working on the mini bike... W/3D printed clip until my metal one arrives....3yr ⋅ JasonJln ⋅ r/Leatherman
LGTOY saber finally arrived.... Better than the last one! Great value saber for the money!4yr ⋅ JasonJln ⋅ r/lightsabers
Lipstick on a pig? Perhaps, but they work great! Suspension actually articulates now!4yr ⋅ JasonJln ⋅ r/ATV
Added onto my first workbench with a smaller version along the back wall. Topped it with 1/8 hardboard, easily replaced if damaged for $3.50 a sheet. Soldering station setup, will put peg board on back wall and install linear PDU for power. Maybe later build in a bottom shelf?4yr ⋅ JasonJln ⋅ r/Workbenches
Any adults here riding smaller quads? I ride a 150cc gy6 that's somewhere between a youth size and 3/4 of a full size atv. Plenty of power for me at 5'9 and 170lbs; can do 30+mph and gets me around the homestead fine. Hauls stuff and is narrow enough to do tight trails.4yr ⋅ JasonJln ⋅ r/ATV
Fitting bolster to Brisa leuku blade; gap on spine side, do I file edge side to close gap?3yr ⋅ JasonJln ⋅ r/knifemaking
Almost all my boys hard at work. A 33hr petg print on the left, a U.S.S. Titan saucer in the middle, and the start of a dragon skull to be lit and painted for Halloween in transparent pla on the right.2yr ⋅ JasonJln ⋅ r/3Dprinting
16 hour print.... Turned out INCREDIBLE...overdid the supports. Anticipate 160 hours of support removal!4yr ⋅ JasonJln ⋅ r/ender3
My temp tower... Input appreciated. Hatchbox black PLA, ring style cooling duct, 0.4 nozzle.4yr ⋅ JasonJln ⋅ r/ender3
Thinking of trimming it down short, think corporate beard. It feels out of control.6yr ⋅ JasonJln ⋅ r/beards
