I 3D printed this little holster for my steam deck on my bedside table.1yr ⋅ GO_Strawbs ⋅ r/SteamDeck
My first Pi project!!! I learned so much from this and can’t wait to keep experimenting and building!6yr ⋅ GO_Strawbs ⋅ r/raspberry_pi
My 5th attempt at this kitchen set. I’m finally close to a perfect set. A small piece broke off the strainer, but other than that...perfect.4yr ⋅ GO_Strawbs ⋅ r/CNC
3D printed some brackets for a shelf above my desk. Used a piece of solid walnut for the shelf.6yr ⋅ GO_Strawbs ⋅ r/3Dprinting
Light pendant designed specifically for the laser cutter. Incorporating string creates a lot of design potential. I think I’ll be experimenting with it more.4yr ⋅ GO_Strawbs ⋅ r/lasercutting
First attempt at building a chair. The challenge was to use no hardware and no glue. All dog-bones and press fit connections. .75” birch ply cut on a Shapeoko3 CNC.4yr ⋅ GO_Strawbs ⋅ r/woodworking
A minimal chair I designed an built with a CNC router. I’m really enjoying using the dog bone method of building furniture. Once you lock in the tolerances it feels like anything is possible. And no hardware needed!4yr ⋅ GO_Strawbs ⋅ r/woodworking
A custom pocket box made for a friend. Zebra wood lined with suede finished with shellac and bees wax.4yr ⋅ GO_Strawbs ⋅ r/woodworking
Made this little dice holder for D&D. CNC milled top “water” pattern. Sanded and finished with shellac.4yr ⋅ GO_Strawbs ⋅ r/woodworking
My 5th attempt at this kitchen set on the CNC. Finally getting close to perfect. Do you think wood glue will hold that little piece of the strainer on tight enough?4yr ⋅ GO_Strawbs ⋅ r/woodworking
Wall sconce. 3D printed the spine with a curving loft. Then mounted 1/2” pieces of Purple Heart wood to the twisting front face. Creates a cool twisting pattern.6yr ⋅ GO_Strawbs ⋅ r/3Dprinting
Playing with 3D printed brackets to make interesting shapes out of wood. Solid birch plank unfinished.6yr ⋅ GO_Strawbs ⋅ r/woodworking
My new shop table! I’ve been slowly upgrading my work space for the last few years and this is a HUGE upgrade in my workflow and organization. Let me know if you guys have any input!4yr ⋅ GO_Strawbs ⋅ r/woodworking
Spider bots. Done on my new iPad Pro with Apple Pencil. Not normally a apple fanboy, but the drawing experience is really nice.6yr ⋅ GO_Strawbs ⋅ r/conceptart
Honeycomb shelves for my office. I laser cut some drawers to cover the mounting hardware.4yr ⋅ GO_Strawbs ⋅ r/woodworking
Taken with my New MavicPro. I'm really amazed by the leap forward in tech by DJI compared to my previous Phantom 3s. Cliffs of Moher, Ireland.7yr ⋅ GO_Strawbs ⋅ r/drones
Practicing my ground setup. In the worst case scenario that there are no trees available. Any thoughts?6yr ⋅ GO_Strawbs ⋅ r/hammockcamping
A small shelf I built over the weekend. Poplar and red oak. Trying to work on my mitered corners.7yr ⋅ GO_Strawbs ⋅ r/woodworking
E-Board heaven up in Big Basin Redwood Forest. My wife on her Evolve Bamboo GT. Me attempting to fly the drone while riding my custom board (Enertion parts).7yr ⋅ GO_Strawbs ⋅ r/ElectricSkateboarding
There were 2 cars on the freeway with generators hitched to the back. The generators had tubes running to some equipment in the back seat. There was also some type of antenna attached to the back window. Any ideas?5yr ⋅ GO_Strawbs ⋅ r/whatisthisthing
Hilarious little tid-bit from your favorite pondering raptor on a Monday morning.7yr ⋅ GO_Strawbs ⋅ r/terriblefacebookmemes
